Відео

What would happen if you place the slide pin bolts in the wrong place, (g in the l, and l in the g)

Are the same guy that give advices on pool care ?

Thank you so much! Perfect video for this job. Straight and to the point! I use a torque wrench because I don't trust myself with that. I do a lot of my own car repairs. Two reasons. One, I know I'll do it right and two it's way cheaper! My Honda Accord has been one issue after another. I've been throwing parts at it for past 5 years. After this repair? I'm selling.

For any newer viewers. He uses Honda ATF-z1. If you’re confused because all yo can find is DW-1 ATF than you’re fine. DW-1 replaced z1 atf years ago because I’m guessing they upgraded a few additives or detergents in it

Thanks for the video man! What sizes are these two o-rings?

Where did you go? Did you stopped making videos?

Thanks for this diy video very helpful however my 95 honda also is locked in gear think it part of the anti theft system see if after the switch and key cylinder replace we be back on the road again .

Great job...Possibly one of the BEST DIY videos out there...Details were all spot on and shown properly...Thanks for also including other pertinent info like not over tightening the battery terminals. Again great job and great advice!!

What is the little tool that looks like a screw driver

I need this belt size to buy it please help

Information never dies! THANKS

Thanks always for the valuable info on the accord. I hope you have made some bucks on these videos...they are most helpful. God bless you bud!

32 cents at the Honda dealer....not any more.

I love You so much

Thanks for the help, used this video to help with radiator replacement in a 96 odyssey

Great job showing all the bolt locations even with so little space and lighting! Best one I've seen in my research to replace a 95 accord starter.

Nice one mate’’Thanks for the Visio’🙏🏼❤️💚💛👊🏻🤘🤛👌☄️

I like your clip.help me to find out why oil is leakage

I had tried to bleed my Abs modulator as shown but no pressure at all, the Abs motor sounds good n function but no fluids out when i open up the bleeder nipple...bad pump?

I tried bleeding the Abs modulator but when i turn the bleeder nipple out nothing hapoened...no brake fluids out. I watched your next video how to bleed Abs, the motor sound ok but no pressure at all...

Where is that clock spring you lined up at the end? I can’t find that thing anywhere lol

Just got an accord and found this channel. It is STILL helping people!

Does the car need to be warmed up right before changing? Can it be done on a cold engine?

To take the axle nut off. Is it okay to use a 36 mm 12 point axle nut socket. Or should I get something else??

Making no promises to anyone but when I did this on a Civic I accidentally spun the distributor lugs. It seemed I had a 50/50 chance of getting it right but when I fiddled about I discovered my distributor lugs are slightly offset so if you're gentle there is only one orientation that will insert. It makes sense really.

What about if the dash lights don't come on

Thanks just perfect. And can u

I have been working on my 96 Accord LX. I was replacing the clutch. However the steering rack was leaking bad and I had to replace it also. It was a little easier to loosen the power steering lines with the axles out of the way. This video is a great resource for the steering rack replacement.

Excellent video. IDK if you still read these... your last video was 6 years ago! But thanks, this was a big help.

Where's the filter change video?

good job 👏🏾 👏🏾 👏🏾

The high-pressure power steering line is not connected where it is on this video on my 1996 Honda Accord EX. I could see the pressure sensor connected underneath the car, but appears as the connection goes down onto the steering rack. I can feel it, but I cannot see it. I’m not sure how I’m going to get to it so that I can disconnect it because I can’t see it.

Thx!

thank you so much.from malaysia

This guy is an MVP. Love being able to follow a problem from the beginning to end.

Great video thank you!!!

I don’t think I would use the power steering fluid to lubricate the O-ring, I would use silicone grease.

Do 1998 EX have one. I cannot see it in my car.

My pin doesn't want to slide out. Tried lightly tapping but still not coming out. What can I do?

What year is Honda? I have 2008 Accord is it same flex pipe?

Thank you, thank you, thank you. I'm glad I found your video, You're awesome.

Part 1 and part 2 gave me the confidence to do this job on my own without having some else do it for me, I’ve done brake pad rotors jobs in the past but never a captive rotor job… thanks for your videos 👍🏽

Man, I have scoured UA-cam for this year, 1999, and all are either the 3.0 or newer models. Totally different setups. Although yours is a bit earlier it's the same exact setup. Thank you

So I did it but my brake pedal down, so what I need to do?

Dude i like this older Honda Accords and your video very helpfull! Thanks!

What will happen if I ride with out the ai box I have a little filter on it but it doesn't run if any moisture gets on it but runs great with out it

Booster leakage is a cause of many on old Honda. Very good video

A 27mm deep socket worked on 90 Accord, if anyone curious.

Espirómetro not working

Where on the vehicle is this located? Near pump or near engine bay? Wosh a lottle zoom out to see the car.